Campbell DC112 Operator's Manual Page 23
- Page / 221
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
21X MICROLOGGER OVERVIEW
OV-11
Display Shows
Key (ID:Data) Explanation
A 02:0000 Enter repetition and advance to the second
parameter which specifies the first Input Storage
location to sample.
1 02:1 Input Storage location 1, where the panel
temperature is stored.
A 04:P00 Enter location and advance to fourth instruction
location. Note that a value is not entered into
memory until A is keyed. If *0 was keyed after the
1 in the previous step, the location would not be
entered and would remain 0.
*0 :LOG 1 Exit Table 1, enter *0 mode, compile program, and
log data.
The 21X is now programmed to measure the panel temperature every 5 seconds and send each
reading to Final Storage. Values in Final Storage can be viewed using the *7 Mode (Section 2.3):
Display Shows
Key (ID:Data) Explanation
*7 07: 13.000 Enter *7 Mode. The Data Storage Pointer (DSP) is
displayed showing the next available Final Storage
Location (location 13 in this example).
A 01: 0102 Advance to the first value, the output array
Identifier (ID). The ID indicates the Output Flag
was set in Table 1 by the second instruction
(Section 2.1).
A 02: 21.23 Advance to the first temperature stored. Note that
there are only 4 digits displayed (low resolution)
while the readings in Input Storage displayed 5
digits (Section 2.2 and Inst. 78).
A 01: 0102 Advance to the next output array. Same output
array ID.
A 02: 21.42 Advance to 2nd stored temp.
*0 :LOG 1 Change to *0 Mode.
In the above example, no time information is stored with the data. In the second example,
Instruction 77 is used to save the time of the measurements.
OV4.2 EDITING AN EXISTING PROGRAM
When editing an existing program in the 21X,
entering a new instruction inserts the
instruction; entering a new value for an
instruction parameter replaces the previous
value.
To insert an instruction, enter the program table
and advance to the position where the
instruction is to be inserted (i.e., P in the data
portion of the display) key in the instruction
number, and then key A. The new instruction
- 21X MICROLOGGER 1
- OPERATOR’S MANUAL 1
- WARRANTY AND ASSISTANCE 3
- 21X OPERATOR'S MANUAL 5
- TABLE OF CONTENTS 5
- OVERVIEW 5
- PROGRAMMING 6
- DATA RETRIEVAL/COMMUNICATION 6
- PROGRAMMING EXAMPLES 7
- INSTRUCTIONS 7
- INSTALLATION 8
- APPENDICES 8
- SELECTED OPERATING DETAILS 9
- This is a blank page 10
- CAUTIONARY NOTES 11
- 21X MICROLOGGER OVERVIEW 13
- CONCEPTS 15
- OV2. MEMORY AND PROGRAMMING 15
- OV3. PROGRAMMING THE 21X 18
- OV4. PROGRAMMING EXAMPLES 20
- OV5. DATA RETRIEVAL OPTIONS 27
- OV6. SPECIFICATIONS 30
- SECTION 1. FUNCTIONAL MODES 31
- CLOCK - *5 MODE 32
- MEMORY OR FLAGS - *6 MODE 32
- 1.5 MEMORY ALLOCATION - *A 34
- STATUS - *B 36
- 1.7 *C MODE -- SECURITY 36
- 1.8 *D MODE -- SAVE OR LOAD 37
- ARRAYS, AND MEMORY POINTERS 41
- 2.2 DATA OUTPUT FORMAT AND 42
- RANGE LIMITS 42
- KEYBOARD/DISPLAY - *7 MODE 43
- 3.1 PARAMETER DATA TYPES 45
- 3.2 REPETITIONS 45
- 3.4 INDEXING INPUT LOCATIONS 45
- 3.5 VOLTAGE RANGE AND 46
- OVERRANGE DETECTION 46
- 3.6 OUTPUT PROCESSING 46
- PROGRAM CONTROL 47
- 3.8 PROGRAM CONTROL LOGICAL 48
- CONSTRUCTIONS 48
- 3.9 INSTRUCTION MEMORY AND 50
- EXECUTION TIME 50
- 3.10 ERROR CODES 53
- 4.1 ON-LINE DATA TRANSFER 55
- INSTRUCTION 96, *4 MODE 55
- 4.2 MANUALLY INITIATED DATA 56
- OUTPUT - *8 AND *9 MODES 56
- 4.3 CASSETTE TAPE OPTION 58
- 4.5 PRINTER OUTPUT FORMATS 61
- 5.1 TELECOMMUNICATIONS 63
- COMMANDS 63
- 6.1 PIN DESCRIPTION 67
- SILICON PYRANOMETER 73
- A COMMON EXTERNAL POWER 73
- USING 21X REFERENCE 74
- USING AN EXTERNAL REFERENCE 74
- JUNCTION 74
- 7.5 107 TEMPERATURE PROBE 75
- WITH LONG LEADS 76
- 7.7 ANEMOMETER WITH 76
- PHOTOCHOPPER OUTPUT 76
- 7.12 PRESSURE TRANSDUCER - 4 80
- WIRE FULL BRIDGE 80
- 7.13 LYSIMETER - 6 WIRE FULL 81
- 7.15 NONLINEAR THERMISTOR IN 83
- HALF BRIDGE (CAMPBELL 83
- SCIENTIFIC MODEL 101) 83
- PROBE WITH 60 HZ REJECTION 84
- 8.1 COMPUTATION OF RUNNING 87
- 8.2 RAINFALL INTENSITY 88
- 8.3 USING CONTROL PORTS AND 89
- LOOP TO RUN AM416 MULTIPLEXER 89
- SYNCHED TO REAL TIME 91
- 8.5 SDM-A04 ANALOG OUTPUT 91
- MULTIPLEXER TO STRIP CHART 91
- 8.6 CONVERTING 0-360 WIND 93
- DIRECTION OUTPUT TO 0-540 FOR 93
- STRIP CHART 93
- 8.7 COVARIANCE CORRELATION 94
- PROGRAMMING EXAMPLE 94
- 8.8 FAST FOURIER TRANSFORM 97
- EXAMPLES 97
- are not 113
- Parameters 6 117
- SECTION 13. 21X MEASUREMENTS 149
- LENGTH ON THE SIGNAL SETTLING 151
- Error (degrees) = 153
- 13.4 THERMOCOUPLE 158
- MEASUREMENTS 158
- 13.5 BRIDGE RESISTANCE 163
- 13.6 RESISTANCE MEASUREMENTS 167
- REQUIRING AC EXCITATION 167
- 14.1 PROTECTION FROM THE 169
- ENVIRONMENT 169
- 14.2 POWER REQUIREMENTS 170
- 14.3 21X POWER SUPPLIES 171
- 14.4 SOLAR PANELS 172
- TO THE 21X 172
- 14.6 VEHICLE POWER SUPPLY 172
- CONNECTIONS 172
- 14.7 USE OF DIGITAL CONTROL 173
- PORTS FOR SWITCHING RELAYS 173
- 14.8 GROUNDING 173
- 14.9 MAINTENANCE 174
- 14.10 CALIBRATION PROCEDURES 174
- APPENDIX A. GLOSSARY 179
- C.1 TELECOMMUNICATIONS 185
- COMMAND WITH BINARY 185
- RESPONSES 185
- C.2 FINAL STORAGE FORMAT 187
- C.3 GENERATION OF SIGNATURE 189
- APPENDIX D. ASCII TABLE 191
- E.1 DISASSEMBLY OF 21X 193
- E.2 INSTALLING NEW RAM CHIPS 193
- E.3 CHANGING PROM CHIPS 194
- 15 SERIAL INPUT 197
- THE AIR-DB-1A BAROMETER 198
- *D TAPE UPLOAD AND DOWNLOAD 203
- LIST OF TABLES 205
- LIST OF FIGURES 209
- 13. 21X MEASUREMENTS 210
- 21X INDEX 211
Related products and manuals for Networking Campbell DC112
Networking Campbell NL120 User Manual
(22 pages)
(22 pages)
Networking Campbell SDM-CAN Specifications
(32 pages)
(32 pages)
Networking Campbell NL115 Manual
(48 pages)
(48 pages)
Networking Campbell SC932A User Manual
(14 pages)
(14 pages)
Networking Campbell CS-GSM/GPRS User's Guide
(22 pages)
(22 pages)
Networking Campbell NL115 Instruction Manual
(40 pages)
(40 pages)
Networking Campbell NL200 Instruction Manual
(60 pages)
(60 pages)
Networking Campbell Redwing 105 User Manual
(14 pages)
(14 pages)
Networking Campbell Raven II Manual
(54 pages)
(54 pages)
Networking Campbell COM9522B User's Guide
(46 pages)
(46 pages)
Networking Campbell COM200 User Manual
(2 pages)
(2 pages)
Networking Campbell COM310 User Manual
(4 pages)
(4 pages)
Networking Campbell NL201 User Manual
(8 pages)
(8 pages)
ONKYO CD Spieler Benutzerhandbücher
Die Liste der ONKYO CD Spieler -Produkte enthält 32 Benutzerhandbücher für 31 diese Modelle. Alle PDF-Benutzerhandbücher können heruntergeladen oder online angezeigt werden.
Comments to this Manuals