Campbell CR800 Specifications Page 181
- Page / 324
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 7. Measurement Instructions
Parameter
& Data Type
Enter
Range Alpha Code
Voltage Range
Constant mV5000
± 5000 mV
mV2500
± 2500 mV
mV250
± 250 mV
mV25
± 25 mV
mV7_5
± 7.5 mV
mV2_5
± 2.5 mV
Autorange
mV2_5 − mV5000
Selects range (Sect. 3.1)
mV250C
± 250 mV The mV250C, mV25C, mV7_5C,
mV25C
± 25 mV and mV2_5C ranges pull the channel
mV7_5C
± 7.5 mV into common mode range and check
mV2_5C
± 2.5 mV for open input
AutorangeC
mV2_5 − mV250
Selects C range
Am25tChan
Constant
The starting input channel on the multiplexer.
DiffChan
Constant
The Differential channel that will be used to make the actual measurements
from the AM25T.
If the channel is entered as a negative number, all reps occur on
that channel.
TCType
Constant
The Thermocouple Type Code. Enter -1 to return voltage measurements.
Tref
Variable
The variable in which to store/read the AM25T reference temperature.
ClkPort
Constant
The Digital Output port number that will be used to clock the AM25T. One
clock port may be used with several AM25Ts.
ResPort
Constant
The Digital Output port number that will be used to enable and reset the
AM25T. Each AM25T must have it's own unique Reset line
VxChan
Constant
The Excitation Channel number that will be used to provide excitation for
the PRT reference temperature measurement. If 0 is entered for the
excitation channel, the temperature is not measured.
RevDiff Code Value
Result (Reversing requires twice as much time to complete)
Constant False 0
Signal is measured with the high side referenced to the low
True ≠0
A second measurement is made after reversing the inputs to
cancel offsets
SettlingTime
Constant
The time in microseconds to delay between setting up a measurement (switching to
the channel, setting the excitation) and making the measurement. (1 microsecond
resolution)
Entry
Voltage Range Integration Settling Time
0
All 250 µS 450 µS (default)
0
All _50Hz, _60 Hz 3 mS (default)
>=100
All All µS entered
Integ The time spent on integration in microseconds for each of the channels measured.
Constant Entry
Integration
250
250 µS
_60Hz or 16667
16,667 µS (reject 60 Hz noise)
_50 Hz or 20000
20,000 µS (reject 50 Hz noise)
Mult, Offset
Constant,
Variable,
Array, or
Expression
A multiplier and offset by which to scale the raw results of the measurement. See
the measurement description for the units of the raw result; a multiplier of one and an
offset of 0 are necessary to output in the raw units. For example, the TCDiff
instruction measures a thermocouple and outputs temperature in degrees C. A
multiplier of 1.8 and an offset of 32 will convert the temperature to degrees F.
7-27
- CR800/CR850 Measurement 1
- Warranty and Assistance 2
- Appendix 7
- Figures 7
- OV1.1.8 Digital I/O (C1-4) 11
- OV1.1.9 Pulse Inputs (P1-2) 12
- OV1.1.10 Program Status 12
- OV1.2.1 CS I/O 12
- OV1.2.2 Computer RS-232 13
- OV2.1 Memory 14
- OV2.2 Programming 14
- OV2.3.1 Pipeline Mode 15
- OV2.3.2 Sequential Mode 15
- OV2.3.3 Slow Sequence Scans 16
- OV2.3.4 Task Priority 16
- OV2.4 Data Tables 17
- OV2.5 PakBus 17
- OV3. Device Configurator 18
- OV3.1 Main DevConfig Screen 19
- OV3.2 Deployment Tab 20
- OV3.2.2 Ports Settings 21
- OV3.2.3 Advanced 23
- OV3.3 Logger Control Tab 24
- OV3.5 Settings Editor Tab 26
- OV3.6 Terminal Tab 27
- OV4. Quick Start Tutorial 28
- OV4.4 PC200W Software 30
- OV4.4.4 Send the Program 35
- OV4.4.5 Monitor Data Tables 35
- OV4.4.6 Collect Data 36
- OV4.4.7 View Data 37
- OV5. Keyboard Display 39
- CR1000KD or CR850 Display 40
- OV5.1 Data Display 41
- CR800 and CR850 Overview 42
- 1.2 Power Requirements 53
- 12V ALKALINE BATTERY PACK 55
- 1.4 Solar Panels 58
- 1.7 CR800 Grounding 59
- 1.10 Maintenance 63
- 1.10.1 Desiccant 64
- 2.1 Data Storage in CR800 69
- 2.2 Internal Data Format 69
- 2.3 Data Collection 70
- 2.4 Data Format on Computer 70
- 3.1.1 Voltage Range 75
- 3.1.4 SettlingTime 77
- Measurements 78
- 3.3 Signal Settling Time 80
- Settling Time 82
- 3.4.1 Error Analysis 83
- Time Minutes 85
- Measured - Actual degrees C 85
- Thermocouple Limits of Error 86
- ± 0.5% Not Estab 86
- Noise on Voltage Measurement 88
- Error Summary 89
- can be minimized by making 90
- CR800 Junction Box 91
- 3.8 Self Calibration 95
- °C) the 96
- °C out into a 96
- Programming 97
- 4.2 Programming Sequence 98
- 4.3 Example Program 100
- CallTable Temp 102
- 4.4 Variable Data Types 103
- 4.5 Numerical Entries 105
- 4.6.1 What is True? 106
- 4.6.2 Expression Evaluation 106
- 4.7 Flags 107
- 4.8 Parameter Types 107
- AngleDegrees 111
- AS type 112
- PipelineMode 114
- SequentialMode 115
- Station Name 115
- Sub, Exit Sub, End Sub 116
- 6.1 Data Table Declaration 119
- 6.2 Trigger Modifiers 120
- OpenInterval 121
- FillStop 123
- DSP4 (FlagVar, Rate) 126
- BufferControl 127
- Remarks 128
- StatusCommand 129
- Highlimit, MinAmp, Form) 144
- Measured raw data: 150
- Calculations: 150
- ΘΘ ΘuNUSsNS 152
- ()(( /)) ( /) 153
- ΘuUS US=− =−21 811 153
- This is a blank page 154
- 7.8 Specific Sensors 156
- 7.9 Peripheral Devices 156
- 7.1 Voltage Measurements 157
- Integ, Mult, Offset) 158
- 7.4 Full Bridges 162
- 7.5 Excitation 164
- 7.6 Self Measurements 165
- Calibrate (Dest, AllRanges) 166
- 7.7 Digital I/O 169
- Timeout, Mult, Offset) 170
- ± 10 mV) and resolution (1.2 171
- Silicon diodes 171
- PortsConfig (Mask, Function) 172
- PortGet (Dest, Port) 172
- PortSet (Port, State) 173
- Constant 174
- ReadIO (Dest, Mask) 176
- Offset) 176
- WriteIO (Mask, Source) 177
- SlowAntenna 179
- Variable 180
- SettlingTime 181
- SDMAddress 184
- TimeQuanta t 185
- SDMSpeed (BitPeriod) 199
- SDMTrigger 199
- SDMX50 (SDMAddress, Channel) 200
- Mult, Offset) 201
- Instructions 203
- ACOS (Source) 204
- ASIN (Source) 206
- ATN (Source) 206
- AvgSpa (Dest, Swath, Source) 208
- Cos (Source) 209
- CosH (Source) 210
- FirstSetStart) 210
- DewPoint (Dest, Temp, RH) 211
- Exp (Numeric Expression) 213
- Frac (Source) 215
- Int, Fix 218
- Ln (Source) 219
- Log (Source) 219
- LOG10 (number) 219
- MaxSpa (Dest, Swath, Source) 220
- MinSpa (Dest, Swath, Source) 220
- Randomize (Number) 227
- RealTime 227
- RectPolar (Dest, Source) 228
- RMSSpa (Dest, Swath, Source) 229
- RND (Source) 229
- SatVP (Dest, Temp) 230
- Sgn (Number) 233
- Sin (Angle) 233
- SinH (Expression) 234
- Sqr (Number) 234
- Tan (Source) 235
- TANH (Source) 236
- Derived Math Functions 239
- Section 9. Program Control 241
- CallTable 242
- Data … Read … Restore 243
- ClockSet (Source) 244
- Delay (Option, Delay, Units) 244
- Do … Loop 245
- FileManage 246
- FileMark (TableName) 247
- For ... Next 247
- RunProgram 251
- ResetTable 252
- Scan … NextScan 252
- SelectCase … EndSelect 253
- Slow Sequence 257
- Timer (TimNo, Units, TimOpt) 259
- WaitDigTrig (Port, Edge) 260
- While…Wend 261
- DisplayMenu/EndMenu 264
- 11.1.1 Constant Strings 267
- 11.1.2 Add Strings 267
- Processing Instructions 268
- LowerCase (SourceString) 269
- StrComp (String1, String2) 270
- UpperCase (SourceString) 270
- Functions 271
- DialVoice (DialString) 272
- BooleanVariable) 273
- SerialClose (ComPort) 274
- SerialFlush (ComPort) 275
- ClockReport 280
- PakBusClock (PakBusAddr) 280
- Routes (Dest) 280
- GetSwath) 281
- TimeOut, Settings) 282
- TimeUntilTransmit 283
- 14.2.2 PakBus Address Setup 291
- 14.2.4 Router Setup 293
- 14.2.5.2 Baud Rates 294
- 14.3 PakBus Concepts 295
- 14.3.2 PakBus Devices 296
- 14.3.3 Neighbor Discovery 296
- 14.3.4 Neighbor Removal 297
- 14.3.6 Routers 298
- 14.3.8 Leaf-Nodes 302
- ComPort_2 303
- PakBusPort 303
- 14.4 Settings Editors 304
Related products and manuals for Measuring, testing & control Campbell CR800
(60 pages)© 2020, manymanuals.com. All rights reserved. | 3.554 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals