Campbell CR800 Specifications Page 201
- Page / 324
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 7. Measurement Instructions
Parameter
& Data Type
Enter
SDMAddress
Constant
The SDMAddress of the SDMX50 to switch. Valid SDM addresses are 0
through 14.
Channel
Constant
The SDMX50 channel to switch to (1-8)
TDR100 (Dest, SDMAddress, Option, Mux/ProbeSelect, WaveAvg, Vp,
Points, CableLength, WindowLength, ProbeLength, ProbeOffset,
Mult, Offset)
This instruction can be used to measure one TDR probe connected to the
TDR100 directly or multiple TDR probes connected to one or more SDMX50
multiplexers.
Parameter
& Data Type
Enter
Dest
The Dest parameter is a variable or variable array in which to store the
results of the measurement. The variable must be dimensioned to
accommodate all of the values returned by the instruction, which is
determined by the Option parameter.
SDMAddress
The SDMAddress parameter defines the address of the TDR100 with which
to communicate. Valid SDM addresses are 0 through 14. Address 15 is
reserved for the SDMTrigger instruction. If the Reps parameter is greater
than 1, the datalogger will increment the SDM address for each subsequent
TDR100 that it communicates with.
Note: CRBasic dataloggers are programmed using the base 10 address (0-
14) Edlog programmed dataloggers (e.g., CR10X, CR23X) used base 4
Option
The Option parameter determines the output of the instruction.
Code Description
0 Measure La/L (ratio of apparent to physical probe rod length)
1 Collect Waveform values - Outputs reflection waveform values as
an array of floating point numbers with a range of -1 to 1. The
waveform values are prefaced by a header containing values of key
parameters for this instruction (averaging, propagation velocity,
points, cable length, window length, probe length, probe offset,
multiplier, offset)
2 Collect Waveform plus First Derivative - Returns (2*n-5)+9 values
where n is the number of waveform reflection values specified by
the Points parameter.
3 Measure Electrical Conductivity - Outputs a value that when
multiplied by the Multiplier parameter determines soil bulk
electrical conductivity in S/m.
Mux/
ProbeSelect
The Mux/Probe Select parameter is used to define the setup of any
multiplexers and attached probes in the system. The addressing scheme
used is ABCR, where A = level 1 multiplexer channel, B = level 2
multiplexer channel, C = level 3 multiplexer channel, and R = the number of
consecutive probes to be read, starting with the channel specified by the
ABC value (maximum of 8). 0 is entered for any level not used.
7-47
- CR800/CR850 Measurement 1
- Warranty and Assistance 2
- Appendix 7
- Figures 7
- OV1.1.8 Digital I/O (C1-4) 11
- OV1.1.9 Pulse Inputs (P1-2) 12
- OV1.1.10 Program Status 12
- OV1.2.1 CS I/O 12
- OV1.2.2 Computer RS-232 13
- OV2.1 Memory 14
- OV2.2 Programming 14
- OV2.3.1 Pipeline Mode 15
- OV2.3.2 Sequential Mode 15
- OV2.3.3 Slow Sequence Scans 16
- OV2.3.4 Task Priority 16
- OV2.4 Data Tables 17
- OV2.5 PakBus 17
- OV3. Device Configurator 18
- OV3.1 Main DevConfig Screen 19
- OV3.2 Deployment Tab 20
- OV3.2.2 Ports Settings 21
- OV3.2.3 Advanced 23
- OV3.3 Logger Control Tab 24
- OV3.5 Settings Editor Tab 26
- OV3.6 Terminal Tab 27
- OV4. Quick Start Tutorial 28
- OV4.4 PC200W Software 30
- OV4.4.4 Send the Program 35
- OV4.4.5 Monitor Data Tables 35
- OV4.4.6 Collect Data 36
- OV4.4.7 View Data 37
- OV5. Keyboard Display 39
- CR1000KD or CR850 Display 40
- OV5.1 Data Display 41
- CR800 and CR850 Overview 42
- 1.2 Power Requirements 53
- 12V ALKALINE BATTERY PACK 55
- 1.4 Solar Panels 58
- 1.7 CR800 Grounding 59
- 1.10 Maintenance 63
- 1.10.1 Desiccant 64
- 2.1 Data Storage in CR800 69
- 2.2 Internal Data Format 69
- 2.3 Data Collection 70
- 2.4 Data Format on Computer 70
- 3.1.1 Voltage Range 75
- 3.1.4 SettlingTime 77
- Measurements 78
- 3.3 Signal Settling Time 80
- Settling Time 82
- 3.4.1 Error Analysis 83
- Time Minutes 85
- Measured - Actual degrees C 85
- Thermocouple Limits of Error 86
- ± 0.5% Not Estab 86
- Noise on Voltage Measurement 88
- Error Summary 89
- can be minimized by making 90
- CR800 Junction Box 91
- 3.8 Self Calibration 95
- °C) the 96
- °C out into a 96
- Programming 97
- 4.2 Programming Sequence 98
- 4.3 Example Program 100
- CallTable Temp 102
- 4.4 Variable Data Types 103
- 4.5 Numerical Entries 105
- 4.6.1 What is True? 106
- 4.6.2 Expression Evaluation 106
- 4.7 Flags 107
- 4.8 Parameter Types 107
- AngleDegrees 111
- AS type 112
- PipelineMode 114
- SequentialMode 115
- Station Name 115
- Sub, Exit Sub, End Sub 116
- 6.1 Data Table Declaration 119
- 6.2 Trigger Modifiers 120
- OpenInterval 121
- FillStop 123
- DSP4 (FlagVar, Rate) 126
- BufferControl 127
- Remarks 128
- StatusCommand 129
- Highlimit, MinAmp, Form) 144
- Measured raw data: 150
- Calculations: 150
- ΘΘ ΘuNUSsNS 152
- ()(( /)) ( /) 153
- ΘuUS US=− =−21 811 153
- This is a blank page 154
- 7.8 Specific Sensors 156
- 7.9 Peripheral Devices 156
- 7.1 Voltage Measurements 157
- Integ, Mult, Offset) 158
- 7.4 Full Bridges 162
- 7.5 Excitation 164
- 7.6 Self Measurements 165
- Calibrate (Dest, AllRanges) 166
- 7.7 Digital I/O 169
- Timeout, Mult, Offset) 170
- ± 10 mV) and resolution (1.2 171
- Silicon diodes 171
- PortsConfig (Mask, Function) 172
- PortGet (Dest, Port) 172
- PortSet (Port, State) 173
- Constant 174
- ReadIO (Dest, Mask) 176
- Offset) 176
- WriteIO (Mask, Source) 177
- SlowAntenna 179
- Variable 180
- SettlingTime 181
- SDMAddress 184
- TimeQuanta t 185
- SDMSpeed (BitPeriod) 199
- SDMTrigger 199
- SDMX50 (SDMAddress, Channel) 200
- Mult, Offset) 201
- Instructions 203
- ACOS (Source) 204
- ASIN (Source) 206
- ATN (Source) 206
- AvgSpa (Dest, Swath, Source) 208
- Cos (Source) 209
- CosH (Source) 210
- FirstSetStart) 210
- DewPoint (Dest, Temp, RH) 211
- Exp (Numeric Expression) 213
- Frac (Source) 215
- Int, Fix 218
- Ln (Source) 219
- Log (Source) 219
- LOG10 (number) 219
- MaxSpa (Dest, Swath, Source) 220
- MinSpa (Dest, Swath, Source) 220
- Randomize (Number) 227
- RealTime 227
- RectPolar (Dest, Source) 228
- RMSSpa (Dest, Swath, Source) 229
- RND (Source) 229
- SatVP (Dest, Temp) 230
- Sgn (Number) 233
- Sin (Angle) 233
- SinH (Expression) 234
- Sqr (Number) 234
- Tan (Source) 235
- TANH (Source) 236
- Derived Math Functions 239
- Section 9. Program Control 241
- CallTable 242
- Data … Read … Restore 243
- ClockSet (Source) 244
- Delay (Option, Delay, Units) 244
- Do … Loop 245
- FileManage 246
- FileMark (TableName) 247
- For ... Next 247
- RunProgram 251
- ResetTable 252
- Scan … NextScan 252
- SelectCase … EndSelect 253
- Slow Sequence 257
- Timer (TimNo, Units, TimOpt) 259
- WaitDigTrig (Port, Edge) 260
- While…Wend 261
- DisplayMenu/EndMenu 264
- 11.1.1 Constant Strings 267
- 11.1.2 Add Strings 267
- Processing Instructions 268
- LowerCase (SourceString) 269
- StrComp (String1, String2) 270
- UpperCase (SourceString) 270
- Functions 271
- DialVoice (DialString) 272
- BooleanVariable) 273
- SerialClose (ComPort) 274
- SerialFlush (ComPort) 275
- ClockReport 280
- PakBusClock (PakBusAddr) 280
- Routes (Dest) 280
- GetSwath) 281
- TimeOut, Settings) 282
- TimeUntilTransmit 283
- 14.2.2 PakBus Address Setup 291
- 14.2.4 Router Setup 293
- 14.2.5.2 Baud Rates 294
- 14.3 PakBus Concepts 295
- 14.3.2 PakBus Devices 296
- 14.3.3 Neighbor Discovery 296
- 14.3.4 Neighbor Removal 297
- 14.3.6 Routers 298
- 14.3.8 Leaf-Nodes 302
- ComPort_2 303
- PakBusPort 303
- 14.4 Settings Editors 304
Related products and manuals for Measuring, testing & control Campbell CR800
(60 pages)© 2020, manymanuals.com. All rights reserved. | 5.189 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals